Spray foam insulation and air sealing are highly effective ways to improve your home's energy efficiency, comfort, and indoor air quality. Whether you're insulating an attic, sealing crawl spaces, upgrading walls, or protecting rim joists in the Omaha area, pricing depends on several factors including project size, foam type, and accessibility. We believe in transparent pricing so you know exactly what to expect before work begins.
Pricing guide
These rates are indicative. Every job is unique: size, access, complexity. Request a free estimate for exact pricing tailored to your situation.
| Service | Price | Details |
|---|---|---|
| Attic Spray Foam Insulation | From $1.50/sq ft | Omaha attics run hot in summer and leak heat fast through cold Zone 5A winters off the Missouri River. We spray foam the attic deck in Dundee, Benson and Midtown homes to stop that heat transfer and quiet summer cooling bills. |
| Closed Cell Spray Foam Insulation | From $1.20/board ft | Closed cell foam resists the humid summer moisture that drives inward through Omaha walls. We spray closed cell along rim joists, foundation walls and crawl spaces across Douglas and Sarpy counties for a tight, strong air barrier that handles dry winter reversal too. |
| Open Cell Spray Foam Insulation | From $0.55/board ft | Open cell foam fills stud bays and attic framing for interior rooms across Omaha's Zone 5A climate. It works well on interior partition walls and vaulted ceilings in Elkhorn and Millard homes where sound control and air sealing matter more than vapor resistance. |
| Wall & Injection Foam Insulation | From $2/sq ft | Wall injection foam fills closed stud cavities in older Dundee and Benson bungalows without opening the plaster. We drill small holes from outside or inside, inject foam to fill the cavity, and patch the finish so balloon-framed walls stop losing heat each winter. |
| Crawl Space Spray Foam Insulation | From $2,500 | Most Omaha homes sit on full basements, but some additions and older outbuildings still have a crawl space underneath. We spray foam across those crawl space walls and band joist area to block the damp air and cold drafts common after heavy Missouri River storms. |
| Rim Joist & Band Joist Spray Foam | From $650 | Every Omaha home with a full basement has a rim joist line that lets cold air and drafts into the floor above. We spray closed cell foam along that perimeter to cut winter heat loss and stop cold floors across Douglas County basements. |
| Garage Spray Foam Insulation | From $1,200 | Garages across Omaha take the full swing of Zone 5A weather, from windy winter cold to hot, humid summer afternoons. We spray foam the garage walls and ceiling, including rooms above attached garages common in Elkhorn and Papillion, to even out temperatures year round. |
| Metal Building & Barndominium Spray Foam | From $1.75/sq ft | Metal shops and barns on acreage across Cass, Saunders and Dodge counties take hard hits from hail and summer heat. We spray foam the interior of the metal skin to stop condensation, quiet hailstorm noise, and hold steady temperatures through Nebraska's swinging seasons. |
| Commercial & New Construction Spray Foam | Free commercial estimate | New construction and commercial builds across Douglas and Sarpy counties get spray foam before drywall closes up. We work with builders and general contractors on attics, walls and crawl spaces to meet the energy code that applies at your address. |
| Insulation Removal | From $950 | Old attic insulation in Midtown and Benson homes often sits flattened and damp from years of humidity. We remove and dispose of the old material so the attic deck is clean and dry before new spray foam goes in across Douglas County. |
| Insulation Replacement & Re-Insulation | From $2,800 | Flattened insulation in older Dundee and Benson attics leaves homes exposed to Omaha's cold windy winters. We pull the old material, air seal top plates and penetrations, then install new spray foam sized for Nebraska's Zone 5A heating and cooling loads. |
| Air Sealing | From $650 | Air leaks around top plates and penetrations drive up Omaha's heating and cooling bills each season. We find and seal the gaps with foam and sealant, then confirm the result with a blower door test for homes across Douglas and Sarpy counties. |
What Affects the Price
- Square Footage and Project Size : Larger projects typically cost less per square foot due to efficiency and material volume discounts. A 1,200 sq ft attic will have a different per-unit cost than a 500 sq ft garage.
- Foam Type (Closed Cell vs. Open Cell) : Closed cell foam ($1.20/board ft) is denser and more expensive but offers superior R-value and moisture resistance. Open cell foam ($0.55/board ft) is more affordable and still provides excellent insulation for many applications.
- Accessibility and Structural Complexity : Hard-to-reach attics, cluttered crawl spaces, or areas with existing insulation removal needs require more labor time and equipment, which increases the overall cost.
- Existing Insulation Removal and Cleanup : If old insulation must be removed before spray foam application, expect additional costs starting at $950. Proper disposal and site preparation ensure a clean, safe installation.
What's included
- Travel included across the Omaha area
- Professional labor & equipment
- Old insulation vacuumed out, bagged & hauled away
- Job site cleanup
- Written estimate before work begins
To get an accurate estimate for your Omaha home, call us at (402) 807-2989 with details about the area you want insulated, whether existing insulation needs removal, and any access concerns. Our team will discuss your specific needs, answer questions about closed cell versus open cell foam, and provide a detailed quote. Most estimates are provided quickly so you can make an informed decision with confidence.
Get an Instant Ballpark Estimate
Pick the job, tell us roughly how much surface has to be covered, and see the range we actually work in. No email wall, no waiting.
Tell us the area to cover and we'll send your free written estimate →
Indicative ranges only. Final pricing depends on the thickness and R-value specified, what has to come out first, access, and whether open or closed cell is the right product. Measured on site at the board foot. Minimum job charges apply on small jobs.